Skip to content
MYRALBE
← Myralbe Insights

Industry analysis

Industrial solar in Europe: storage and controls add value

Industrial solar creates opportunities across storage, power conversion, controls and electrical integration. The strongest commercial proposition connects those technologies to how a site consumes electricity and makes investment decisions.

Rooftop solar panels on an industrial building with battery storage cabinets alongside it.

A large industrial roof makes the potential for solar generation visible. The more demanding question is how that electricity will contribute to the business operating beneath it.

A factory, logistics centre and refrigeration facility may have similar roof areas but very different consumption patterns. Their investment decisions depend on production schedules, electricity contracts, existing equipment and future plans. Those differences create opportunities for suppliers that can connect solar generation with a useful operating purpose.

For storage, power conversion and energy management suppliers, the commercial task is to explain where their technology improves the proposed installation and what information is needed to assess that contribution.

Europe’s rooftop opportunity needs a site-level business case

A January 2026 study from the European Commission’s Joint Research Centre estimated approximately 500 GWp of technical rooftop photovoltaic potential on non-residential buildings in the EU. This is an estimate of the available resource; individual sites still require assessment of their structural, electrical and commercial suitability.

Spain already demonstrates the significance of generation at the point of consumption. In its assessment of 2025, Red Eléctrica reported that solar photovoltaic would lead the national generation mix when the estimated contribution of self-consumption installations was included.

These findings give suppliers a reason to examine the market closely. Commercial qualification must then identify which sites have a relevant requirement and which organisations can act on it.

The size of a roof cannot establish how much electricity the business will use when the panels are producing. Nor does it establish the value of exporting any surplus.

Rooftops and solar parks involve different purchasing decisions

The European Commission expects solar growth to include both large installations and increased self-consumption through rooftop systems. Each creates a different commercial setting for equipment suppliers.

A large solar park may involve a developer, asset owner, engineering team and construction contractor defining a generation project. An industrial rooftop installation also has to fit the operating business: its building, electricity use, investment criteria and production requirements.

For a supplier, those distinctions affect who should receive the proposal. A plant owner considering self-consumption may need to be approached through its energy or facilities team. A component intended for a standardised solar-and-storage package may instead be evaluated by an integrator or equipment manufacturer.

A market strategy becomes more useful when it identifies the particular decision the product can influence.

Start with the site’s working day

Consider three hypothetical customers: a factory running two shifts, a cold-storage facility operating continuously and a warehouse that closes at weekends. Each could evaluate the same solar capacity differently.

The assessment should compare expected generation with measured consumption over relevant intervals. Seasonal variation, shutdown periods and planned changes to the business also matter. The Joint Research Centre’s PVGIS resource provides location-specific information on photovoltaic performance and how production changes through the year. That generation information can inform the discussion alongside the customer’s own consumption data.

Commercial questions then become concrete. How much production can be used directly? What happens to the surplus? Which costs change when grid purchases fall? Does a planned charging installation or additional production shift alter the calculation?

The customer’s actual electricity contract belongs in that assessment. A proposal should make its assumptions about purchased electricity, exported energy and operating schedules visible, so that the customer can judge how the case changes if those assumptions change.

Give storage and controls a defined job

Storage should enter the discussion through an identified requirement. That may involve using part of the solar output later, managing a relevant demand peak or supporting another agreed operating objective.

The evaluation needs to consider the additional equipment cost, energy losses, expected battery use and applicable operating limits. A battery’s contribution should be assessed against what the site would do without it.

Controls have an equally practical role. In a suitable installation, they can coordinate generation, storage and selected loads. The specification should establish what can be controlled, what limits must be respected and which business activities take priority.

For an energy management supplier, this means connecting software functions to decisions the customer needs to make. A useful demonstration might show how the proposed system would manage a documented operating schedule or respond to a specified limit. The customer can then evaluate an application with clear assumptions.

Develop the commercial route around the application

Industrial solar projects can create opportunities for complete storage systems, converters, monitoring equipment, controls and associated electrical infrastructure. Each product reaches the market through its own purchasing chain.

A supplier should establish whether its prospective customer buys directly, relies on an engineering partner or selects equipment through an integrator. It should also identify who controls the building, who holds the electricity contract and who approves the investment. Those responsibilities may be divided between several parties.

Myralbe’s energy storage and grid integration work addresses these commercial relationships in Spain, Portugal and France. We help identify suitable applications, reach prospective customers and partners, qualify requirements and coordinate discussions with the supplier’s technical team.

For a manufacturer or software supplier, the most useful starting point is a clear account of the problem its technology can address. That creates a stronger basis for customer conversations, technical evaluation and sustained commercial development.

Does your company supply storage, power conversion or energy controls for commercial and industrial solar applications? Contact Myralbe to discuss the customers, partners and markets relevant to your offer.

Related articles and services